OSSLab::開放軟體實驗室(Open Source Software Lab) > 硬體研究 > 嵌入式系統與硬體 - Embedded System and Hardware > NextVOD unit Hacking - 網樂通改機 > 子專案:NextNAS > 2.如何安裝wheezy版
內容表格
- 1. Wonderbox2.0 release !! (20131231) 程式會自動更新，舊版無需重裝~ 1.WEB UI增加IPCAM/WEBCAM管理介面
- 2. 2.最新刷機改成用sh4twbox 0.9.2 網樂通萬用改機救援碟改機 可參考 http://www.twpda.com/2013/09/sh4twbox-07.html 線上刷機請輸入 http://stwp26.cyberhood.net.tw/NextNAS/target.NexNAS-wheezy-sh4twbox092.tgz
- 3. 注意事項: 1.第一次刷機時最好手動format USB DOM,刪除partiton 2,3,4 然後新增一個partition 2 2.partiton1改成FAT16 3.再執行sh4twbox --> p2 進行安裝
NextNAS for wheezy版 (未來的功能會以此版為主)
1.已啟用服務wonderbox、transmission 、dropbear
2.增加一個救援IP(192.168.168.168)
3.可利用CVBS(AV端子)接螢幕作console登入
4.kernel版本2.6.32-59,已支援UVC ,EXT4
5.root密碼wb1234
6.Wonderbox web UI => http://<NextNAS-ip>:8101 (預設帳/密=>admin)
官方討論區: http://forum.wonderbox.net.tw
2.
注意事項:
1.第一次刷機時最好手動format USB DOM,刪除partiton 2,3,4 然後新增一個partition 2
2.partiton1改成FAT16
3.再執行sh4twbox --> p2 進行安裝
PS.在此特別感謝Chia-Cheng Huang、林原志 、徐皓等開發團隊的幫忙...
註: 常有人問怎麼還要錢?(試用600 天)其實這版是FREE 的.
我們希望真的有在用的人在到期時，再來申請終身免費..
當然如果你覺得功能很實用的話也可以贊助我們開發~謝謝!
贊助方式請利用後台UI，直接點選 '前往付費'
- Was this page helpful?
- 標籤 (Edit tags)
- 什麼連接到這裡
文件 2
| 文件 | 大小 | 日期 | 附件上傳者 | |||
|---|---|---|---|---|---|---|
| inst-01p.jpg 無描述 | 108.16 KB | 11:45, 31 Dec 2013 | chark | 動作 | |
| inst-02.jpg 無描述 | 50.88 KB | 11:45, 31 Dec 2013 | chark | 動作 | |
| Images 2 | ||
|---|---|---|
 |  | |
Powered by MindTouch Core
你是在那個平台作的?
有錯誤訊息嗎? 編輯者 03:46, 6 Nov 2013
此版可由console登入
我按照上面的方式成功安裝好 "USB自動安裝DD檔"
現在我想要安裝busybox這個套件
參照網址"http://www.twpda.com/2012/10/inside-nextvod-replace-busybox.html"
我是直接下載他們網站給的，封裝好的 busybox
到"編譯方式"之前都沒問題
執行編譯方式的第一行"apt-get install libncurses5-dev # under STLinux 2.3"
就出現了問題
root@NextNAS-wheezy:/# apt-get install libncurses5-dev # under STLinux 2.3
Reading package lists... Done
Building dependency tree
Reading state information... Done
The following extra packages will be installed:
libtinfo-dev
Suggested packages:
ncurses-doc
The following NEW packages will be installed:
libncurses5-dev libtinfo-dev
0 upgraded, 2 newly installed, 0 to remove and 14 not upgraded.
Need to get 0 B/298 kB of archives.
After this operation, 1111 kB of additional disk space will be used.
Do you want to continue [Y/n]? y
WARNING: The following packages cannot be authenticated!
libtinfo-dev libncurses5-dev
Install these packages without verification [y/N]? y
/usr/bin/dpkg: unrecognized option '--status-fd'
BusyBox v1.20.2 (2013-04-28 04:05:18 CST) multi-call binary.
Usage: dpkg [-ilCPru] [-F OPT] PACKAGE
Install, remove and manage Debian packages
-i,--install Install the package
-l,--list List of installed packages
--configure Configure an unpackaged package
-P,--purge Purge all files of a package
-r,--remove Remove all but the configuration files for a package
--unpack Unpack a package, but don't configure it
--force-depends Ignore dependency problems
--force-confnew Overwrite existing config files when installing
--force-confold Keep old config files when installing
localepurge: Disk space freed in /usr/share/locale: 0 KiB
localepurge: Disk space freed in /usr/share/man: 0 KiB
Total disk space freed by localepurge: 0 KiB
E: Sub-process /usr/bin/dpkg returned an error code (1)
請問這是什麼樣的問題??
因為我想要用這個網站"shpkg 自製網樂通套件管理" "http://www.twpda.com/2013/01/stlinux-615-shpkg.html"
root@NextNAS-wheezy:~# apt-get install libncurses5-dev
Reading package lists... Done
Building dependency tree
Reading state information... Done
The following extra packages will be installed:
libtinfo-dev
Suggested packages:
ncurses-doc
The following NEW packages will be installed:
libncurses5-dev libtinfo-dev
0 upgraded, 2 newly installed, 0 to remove and 14 not upgraded.
Need to get 298 kB of archives.
After this operation, 1111 kB of additional disk space will be used.
Do you want to continue [Y/n]? y
WARNING: The following packages cannot be authenticated!
libtinfo-dev libncurses5-dev
Install these packages without verification [y/N]? y
Get:1 http://www.si-linux.co.jp/pub/debian-sh/wheezy-sh4/ wheezy/main libtinfo-dev sh4 5.9-10 [93.6 kB]
Get:2 http://www.si-linux.co.jp/pub/debian-sh/wheezy-sh4/ wheezy/main libncurses5-dev sh4 5.9-10 [204 kB]
Fetched 298 kB in 1s (224 kB/s)
Selecting previously unselected package libtinfo-dev:sh4.
(Reading database ... 25481 files and directories currently installed.)
Unpacking libtinfo-dev:sh4 (from .../libtinfo-dev_5.9-10_sh4.deb) ...
Selecting previously unselected package libncurses5-dev.
Unpacking libncurses5-dev (from .../libncurses5-dev_5.9-10_sh4.deb) ...
Setting up libtinfo-dev:sh4 (5.9-10) ...
Setting up libncurses5-dev (5.9-10) ...
localepurge: Disk space freed in /usr/share/locale: 0 KiB
localepurge: Disk space freed in /usr/share/man: 0 KiB
Total disk space freed by localepurge: 0 KiB
root@NextNAS-wheezy:~#
我的在"Install these packages without verification [y/N]? y" 之後就和您的不一樣了
我是直接使用 "USB自動安裝DD檔" 之後就只有安裝NO-IP而已
其他就沒再安裝什麼了
然後最後一行有出現E: Sub-process /usr/bin/dpkg returned an error code (1)
我把你說的apt-get update做了 "http://pastie.org/8467980"
接下來我把busybox-1.21.0-1.txz放到根目錄
解壓縮出來，下ln -s etc/inittabBB etc/inittab指令 "http://pastie.org/8468001"
接下來執行apt-get install libncurses5-dev 就悲劇了 "http://pastie.org/8468014"
原本接下去的話要執行make mrproper
root@NextNAS-wheezy:/# make mrproper
make: *** No rule to make target `mrproper'. Stop.
我是在根目錄下make的，還是不是根目錄下make
還是我的網路通整個用"USB自動安裝DD檔" 再重新弄一次看會不會好?
參考網站"http://www.twpda.com/2012/10/inside-nextvod-replace-busybox.html"
在NextNAS-wheezy下是可以作的
你參考的http://www.twpda.com/2012/10/inside-nextvod-replace-busybox.html
是早期的作法，不適用在此版且也不能直接換!
因為rootfs不同~
請確認你要的是什麼?
聽同學說裝了方便很多
您提到說NextNAS-wheezy下不能使用這種的做法
那有其他的方法可以reference的嗎
對了，我昨天試著安裝別的東西
也是不行 "http://pastie.org/8469307"
好像下載都還可以，安裝就裝不上去了QQ
抱歉，再問一個蠢問題
NextNAS-wheezy 是屬於Debian還是ArchLinux的? 編輯者 07:41, 10 Nov 2013
這個才是最方便的，他是一個OS，AP更多了
早期的版本是用busybox建置系統
現在的版本可作的事更多了!
你現在要重刷一次，修正一下之前所作的錯誤~ 編輯者 01:10, 11 Nov 2013
busybox 簡單來說就是簡化版的 Linux 指令集，主要用於 Embedded Linux。
也因為是簡化版，所以功能完整性是不如 Debian 內建指令。
另外，我想請問你是 twpad.com 官網的站長？
您的意思是說重刷過NextNAS for wheezy版 (Target.tgz或USB自動安裝DD檔 任選刷入都可以嗎?)
再去執行apt-get install libncurses5-dev
看能不能安裝成功嗎?
chark大說的對，我們都只是開發者
而且我只是一個菜菜鳥XDD
可以當開發平台!
但不要把busybox放在這台上，因為是不同的rootFS ~
希望你能了解我所說的~
目前已經可以正常使用中^^
請問chark大 這版的NextNAS-wheezy
可以像這個網站的這樣 有LXDE with HDMI output 或者 XFCE with CVBS output
安裝是這樣嗎 "apt-get install xorg xserver-xorg lxde-core"
參考網站"https://sites.google.com/site/debiansh4/updates/muqiankaifajindujiezhi20130921"
LXDE with HDMI output "https://sites.google.com/site/debiansh4/_/rsrc/1380508504340/home/1279006_10200795931045974_1856731639_o.jpg?height=240&width=320"
XFCE with CVBS output
"https://sites.google.com/site/debiansh4/_/rsrc/1379770558735/home/1071609_10200440540681437_229879743_o.jpg.1379770558537.jpg?height=240&width=320"
root@NextNAS-wheezy:/#
Message from syslogd@NextNAS-wheezy at Nov 26 09:21:06 ...
kernel:journal commit I/O error
我的版本是: 0.92
root@NextNAS-wheezy:/# uname -a
Linux NextNAS-wheezy 2.6.32.59_stm24_0211-PDK7105-32BITS #46 PREEMPT Wed Oct 30 07:57:11 CST 2013 sh4 GNU/Linux
當然也可以把OS轉至外接HDD~
重新檢查機器, 果然是DM有問題. 更新DOM後測試至今沒再發生 I/O error issue. Thanks a lot.
我想請問說我最近安裝了aria2 (已成功安裝)
看到有aria2 有Web UI的介面 "http://ppt.cc/p-2A"
是需要把Aria2Web載下來裝上去就可以了嗎? 還是Debian下不行
可以的話該怎麼裝呢?
應該會有人可以回覆你!
我去請教看看
感謝您!
我看了需要的套件有：httpd、php、php-xmlrpc、aria2、unzip
(aria2就是原本的套件，unzip單純做解壓縮而已)
那麼現在的wheezy有httpd、php、php-xmlrpc這幾個套件嗎
還是需要自行裝入呢?
1.第一次刷機時最好手動format USB DOM,刪除partiton 2,3,4 然後新增一個partition 2
2.partiton1改成FAT16
這2項要怎麼做?? 謝謝 編輯者 08:34, 14 May 2014
執行fdisk -l 看目前抓到的HDD有那些?主要是要調8G的那個!(假如是/dev/sda)
重新調整分割區,以合併2,3,4分割區
fdisk 將 partition 2,3,4 取消建立第二個 partition, 儲存新的 partition table
1. 指令 fdisk /dev/sda 會出現 Command (m for help):
2. 指令 d 會出現Partition number (1-4): 依序輸入2 3 4後(請勿輸入1，會清除原有的救援碟)
3. 指令 n p 然後按下兩次enter等待回到Command (m for help):後輸入w
即可完成2,3,4合併的動作 編輯者 10:49, 15 May 2014
之後我打 fdisk -l 出現/dev/sda1 跟/dev/sda2 編輯者 10:55, 15 May 2014
Wonderbox web UI => http://<NextNAS-ip>:8101 (預設帳/密=>admin)
4.如何對遠端BT種子的操作 ?
==>7.點選新增的BT裝置，可進行參數調整->種子設定->下載設定 編輯者 03:17, 19 May 2014
你知道你灌完後得到的IP嗎?
如: 192.168.1.100
你就連http://192.168.1.100:8101
可利用telnet檢測8101 port是否有通?
telnet 192.168.1.100 8101
建議重裝!
你只是用USB開機，沒有刷機!
執行sh4twbox ->執行線刷(如上面圖示)
-->輸入 http://stwp26.cyberhood.net.tw/NextNAS/target.NexNAS-wheezy-sh4twbox092.tgz 編輯者 02:29, 11 Jun 2014
target disk device(default:sda) : sda
source file put on device or none (default:/dev/sdb1) : none
NAS/target.NexNAS-wheezy-sh4twbox092.tgzo) : http://stwp26.cyberhood.net.tw/NexttNAS/target.NexNAS-wheezy-sh4twbox092.tgz
Wed Jun 11 09:52:37 CST 2014 RED LED indicates installing...
set to red
Info: myfdisk sda del 1 0 0
The number of cylinders for this disk is set to 5157.
There is nothing wrong with that, but this is larger than 1024,
and could in certain setups cause problems with:
1) software that runs at boot time (e.g., old versions of LILO)
2) booting and partitioning software from other OSs
(e.g., DOS FDISK, OS/2 FDISK)
Command (m for help): Partition number (1-4): Info: myfdisk sda del 2 0 0
The number of cylinders for this disk is set to 5157.
There is nothing wrong with that, but this is larger than 1024,
and could in certain setups cause problems with:
1) software that runs at boot time (e.g., old versions of LILO)
2) booting and partitioning software from other OSs
(e.g., DOS FDISK, OS/2 FDISK)
Command (m for help): Partition number (1-4): Info: myfdisk sda new 1 fat16 32
The number of cylinders for this disk is set to 5157.
There is nothing wrong with that, but this is larger than 1024,
and could in certain setups cause problems with:
1) software that runs at boot time (e.g., old versions of LILO)
2) booting and partitioning software from other OSs
(e.g., DOS FDISK, OS/2 FDISK)
Command (m for help): You must delete some partition and add an extended partiti
on first
Command (m for help): Info: myfdisk sda new 2 ext234 auto
The number of cylinders for this disk is set to 5157.
There is nothing wrong with that, but this is larger than 1024,
and could in certain setups cause problems with:
1) software that runs at boot time (e.g., old versions of LILO)
2) booting and partitioning software from other OSs
(e.g., DOS FDISK, OS/2 FDISK)
Command (m for help): You must delete some partition and add an extended partiti
on first
Command (m for help): Info: Wed Jun 11 09:52:40 CST 2014 format /dev/sda2 ext4
mke2fs 1.41.14 (22-Dec-2010)
/dev/sda2 is mounted; will not make a filesystem here!
09:52:40[1]root@sh4twbox ~ #
df 一下看看
開機後,df 的結果如下:
10:38:44[0]root@sh4twbox ~ # df
Filesystem 1K-blocks Used Available Use% Mounted on
10:38:48[0]root@sh4twbox ~ #
fdisk -l 看看!
Disk /dev/sda: 1010 MB, 1010826752 bytes
64 heads, 32 sectors/track, 963 cylinders
Units = cylinders of 2048 * 512 = 1048576 bytes
Device Boot Start End Blocks Id System
/dev/sda1 1 360 368624 6 FAT16
Disk /dev/sdb: 8027 MB, 8027897856 bytes
160 heads, 19 sectors/track, 5157 cylinders
Units = cylinders of 3040 * 512 = 1556480 bytes
Device Boot Start End Blocks Id System
/dev/sdb1 1 203 308550+ 83 Linux
/dev/sdb2 204 406 308560 83 Linux
/dev/sdb3 407 4546 6292800 83 Linux
/dev/sdb4 4547 5139 901360 83 Linux
10:46:06[0]root@sh4twbox ~ #
1.先用fdisk /dev/sdb 將partition2,3,4刪除
2.執行sh4twbox
target disk device(default:sda) : sdb (確認Sdb是8G的USB DOM)
source file put on device or none (default:/dev/sdb1) : none
NAS/target.NexNAS-wheezy-sh4twbox092.tgzo) : http://stwp26.cyberhood.net.tw/NexttNAS/target.NexNAS-wheezy-sh4twbox092.tgz
執行sh4twbox
11:18:47[0]root@sh4twbox ~ # sh4twbox
===== Disk Partition Listing (fdisk -l) ===================
Disk /dev/sda: 1010 MB, 1010826752 bytes
64 heads, 32 sectors/track, 963 cylinders
Units = cylinders of 2048 * 512 = 1048576 bytes
Device Boot Start End Blocks Id System
/dev/sda1 1 360 368624 6 FAT16
Disk /dev/sdb: 8027 MB, 8027897856 bytes
160 heads, 19 sectors/track, 5157 cylinders
Units = cylinders of 3040 * 512 = 1556480 bytes
Device Boot Start End Blocks Id System
/dev/sdb1 1 203 308550+ 83 Linux
===========================================================
Hostname:sh4twbox
Uptime : 11:19:11 up 3 min, 1 users, load average: 0.26, 0.20, 0.09
Free Mem:219 MB
IP Addr :192.168.0.104 192.168.168.168
boot from
last command:
root pts/0 192.168.0.105:57 Wed Jun 11 11:16 still logged in
===========================================================
=== sh4twbox v0.9.2 MENU ===
1) Back to Shell (default)
2) Set Time (Wed Jun 11 11:19:11 CST 2014)
9) Reboot
p2) format first two partitions and install sh4twbox or other OS
p1) Replace one partition and install sh4twbox or other OS
h) show more choice options
============ Please Enter Number:
p2
target disk device(default:sdb) : sdb
source file put on device or none (default:/dev/sda1) : none
source file or download URL (default:auto) : http://stwp26.cyberhood.net.tw/Next
NAS/target.NexNAS-wheezy-sh4twbox092.tgz
Wed Jun 11 11:20:17 CST 2014 RED LED indicates installing...
set to red
Info: myfdisk sdb del 1 0 0
The number of cylinders for this disk is set to 5157.
There is nothing wrong with that, but this is larger than 1024,
and could in certain setups cause problems with:
1) software that runs at boot time (e.g., old versions of LILO)
2) booting and partitioning software from other OSs
(e.g., DOS FDISK, OS/2 FDISK)
Command (m for help): Selected partition 1
Command (m for help): Info: myfdisk sdb del 2 0 0
The number of cylinders for this disk is set to 5157.
There is nothing wrong with that, but this is larger than 1024,
and could in certain setups cause problems with:
1) software that runs at boot time (e.g., old versions of LILO)
2) booting and partitioning software from other OSs
(e.g., DOS FDISK, OS/2 FDISK)
Command (m for help): Selected partition 1
Command (m for help): Info: myfdisk sdb new 1 fat16 32
The number of cylinders for this disk is set to 5157.
There is nothing wrong with that, but this is larger than 1024,
and could in certain setups cause problems with:
1) software that runs at boot time (e.g., old versions of LILO)
2) booting and partitioning software from other OSs
(e.g., DOS FDISK, OS/2 FDISK)
Command (m for help): Command action
e extended
p primary partition (1-4)
Info: myfdisk sdb new 2 ext234 auto
The number of cylinders for this disk is set to 5157.
There is nothing wrong with that, but this is larger than 1024,
and could in certain setups cause problems with:
1) software that runs at boot time (e.g., old versions of LILO)
2) booting and partitioning software from other OSs
(e.g., DOS FDISK, OS/2 FDISK)
Command (m for help): Command action
e extended
p primary partition (1-4)
Info: Wed Jun 11 11:20:19 CST 2014 format /dev/sdb2 ext4
mke2fs 1.41.14 (22-Dec-2010)
Could not stat /dev/sdb2 --- No such file or directory
The device apparently does not exist; did you specify it correctly?
11:20:19[1]root@sh4twbox ~ #
Disk /dev/sda: 1010 MB, 1010826752 bytes
64 heads, 32 sectors/track, 963 cylinders
Units = cylinders of 2048 * 512 = 1048576 bytes
Device Boot Start End Blocks Id System
/dev/sda1 1 360 368624 6 FAT16
Disk /dev/sdb: 8027 MB, 8027897856 bytes
160 heads, 19 sectors/track, 5157 cylinders
Units = cylinders of 3040 * 512 = 1556480 bytes
Device Boot Start End Blocks Id System
/dev/sdb1 1 203 308550+ 83 Linux
17:23:33[0]root@sh4twbox ~ #
應該是少了這個!!
程式會作~
我分割完之後
再刷機時他出現了
/dev/sdb2 is mounted; will not make a filesystem here!
不知道這是麼樣的問題
看看目前的partition分佈~
或重新開機重刷看看!