Skip to main content

網路管理

ip
# 顯示所有網卡資訊
ip addr
ip a

# 顯示所有網卡的 IP
ip -br -c addr show  # 需要較新版 ip

# 顯示 eth0 網卡資訊
ip a show eth0 

# 開啟/關閉網卡
ip link set eth0 { up | down }

# 顯示所有的網路裝置
ip link show
ip -br -c link show
ip l show

# 設定 IP (非永久)
ip a add 192.168.1.200/255.255.255.0 dev eth0

# 移除 IP (非永久)
ip a del 192.168.1.200/255.255.255.0 dev eth0

# 顯示 default gateway 及路由表
ip route show
ip r show
ip route add 10.10.20.0/24 via 192.168.50.100 dev eth0
ip route del 10.10.20.0/24

# Default gateway
ip route add default via 192.168.50.100

# 網路即時狀態
ip -s link 

# 顯示 ARP 紀錄 (NOTE: 查詢連接網路設備的 MAC address 與 IP 對應表)
ip neigh show
ip n show

# 清除 ARP 清單裡的某個 IP 紀錄
ip -s -s n f <ip-address>

# 線上求助
ip a help

在多個網路埠的主機上，如何得知哪些埠有接上網路線

nmcli
# List all of ethernet devices
nmcli con show
nmcli con show <conn-name>
nmcli dev status
# see only the active connections
nmcli con show -a

# Restart the network adapter enp0s3
nmcli con down enp0s3 && nmcli con up enp0s3

# Configure the static ip
nmcli con mod enp0s3 ipv4.addresses 192.168.20.170/24
nmcli con mod enp0s3 ipv4.gateway 192.168.20.1
nmcli con mod enp0s3 ipv4.method manual
nmcli con mod enp0s3 ipv4.dns "8.8.8.8"

nmcli con down enp0s3
nmcli con up enp0s3 

# make a new ethernet connection with name Myhome1, assigned to device enp0s3
nmcli con add type ethernet con-name Myhome1 ifname enp0s3 ip4 192.168.1.50/24 gw4 192.168.1.1
cat /etc/sysconfig/network-scripts/ifcfg-Myhome1
GUI to Configure Network
nmtui
Ubuntu/Debian Configure Network

sudo vi /etc/network/interfaces

auto eth0
iface eth0 inet static
address 10.1.1.201
netmask 255.255.255.0
network 10.1.1.0
broadcast 10.1.1.255
gateway 10.1.1.254
dns-nameservers 10.1.1.254
dns-search my.domain.com
nc - netcat
# Scanning the port range (20 - 1024)
nc -z 192.168.21.202 20-1024

Connection to 192.168.21.202 22 port [tcp/ssh] succeeded!
Connection to 192.168.21.202 80 port [tcp/http] succeeded!
Connection to 192.168.21.202 111 port [tcp/sunrpc] succeeded!
Connection to 192.168.21.202 443 port [tcp/https] succeeded!
Connection to 192.168.21.202 514 port [tcp/shell] succeeded!

# Scanning the specified port
nc -zv 192.168.21.202 21
nc: connect to 192.168.21.202 port 21 (tcp) failed: Connection refused

# Port Scanning With netcat including displaying version #
echo "QUIT" | nc 192.168.2.17 22
echo "QUIT" | nc -v 192.168.2.254 ssh
# OR pass the -vv  to get remote OpenSSH version # 
nc -vv 192.168.2.254 ssh

nc : 在不同的 Linux 主機上傳輸檔案

# Install nc and pv
yum install netcat pv

# Machine A with IP : 192.168.0.4
# Machine B with IP : 192.168.0.7
# On Linux Machine A
# [*] tar -zcf = tar is a tape archive utility used to compress/uncompress archive files 
#     and arguments -c creates a new .tar archive file, -f specify type of the archive file 
#     and -z filter archive through gzip.
# [*] CentOS-7-x86_64-DVD-1503.iso = Specify the file name to send over network, it can be file 
#     or path to a directory.
# [*] pv = Pipe Viewer to monitor progress of data.
# [*] nc -l -p 5555 -q 5 = Networking tool used for send and receive data over tcp 
#     and arguments -l used to listen for an incoming connection, -p 555 specifies the source port 
#     to use and -q 5 waits the number of seconds and then quit.
tar -zcf - CentOS-7-x86_64-DVD-1503.iso | pv | nc -l -p 5555 -q 5

# On Linux Machine B
nc 192.168.1.4 5555 | pv | tar -zxf -
mii-tool
# Installation 
sudo apt install net-tools

# CHECK A SINGLE INTERFACE
sudo mii-tool <interface_name>

# SEE DETAILED INFORMATION
sudo mii-tool -v <interface_name>

# SET NETWORK INTERFACE SPEED
sudo mii-tool –force 10baseT-FD <interface_name>

# RESTART AUTO-NEGOTIATION
# Network devices use an auto-negotiation protocol to communicate the technologies they support. 
# It will then select the fastest mutually supported technology. 
# To restart the auto-negotiation of the interface, run the following command.
sudo mii-tool –restart <interface_name>

# CHANGE THE DUPLEX MODE
# For example, here I have set the speed of the eth0 interface to 10 Mbps and the duplex mode to half-duplex.
sudo mii-tool -F 10baseT-HD eth0

# REPORT LINK STATUS CHANGES
# Run the following command to watch a single interface and report changes in the link status. 
# That is to say, the interfaces are listed at one second intervals by default.
sudo mii-tool -w <interface>

# REPORT LINK STATUS
sudo mii-tool -l <interface_name>

# RESET THE CONFIGURATIONS
# Most importantly, you should be able to reset it to its default configuration 
# if something goes wrong. For that, run the following command
sudo mii-tool -R <Interface_name>
systemctl
# Bringing UP/Down Network Interface
systemctl restart network
# or
systemctl restart network.service

 

Back to top